Here's Your Proof Shufflin!

[Schriv]

Punch..
Did you make any adjustments to the gas regulator when you were having problems with the short stroking? And, make sure the gas plug is not set in the grenade launching position. That is a common problem for folks that aren't familiar with the FALs tuneable gas system.

[timshufflin]

Punch..
Did you make any adjustments to the gas regulator when you were having problems with the short stroking? And, make sure the gas plug is not set in the grenade launching position. That is a common problem for folks that aren't familiar with the FALs tuneable gas system.

I can assure you that our clown, Punch, did not fall victim to these nefarious beginner problems. He's more of a clown than that.

[Oh Mr. Wilson]

Nice rifle Punch! Looks like new.

Here in NY pre-ban mags are legal and they can be used in post ban guns, a lot of folks think they can't. We are not required to have the CA style mag releases. Our Assault weapon ban was put in place while the Clinton ban was still in effect. The law reads that manufactures must date mags. Funny thing is now that the Clinton band sunset magazine manufactures aren't dating mags anymore. So if you have a unmarked mag there is really no way for "them" to tell if they are post or pre-ban, on most of them anyways. I have heard they can identify a few, like some Beretta mags that has a current part number stamped in them. It's driving of few of the Liberal law makers nuts here.

From where I live I can drive down to PA and be back home in two hours. One of the state turds did just that last spring, he went to PA gunshops with a film crew in tow and showed how he could buy hi cap mags just over the boarder. The story lasted about two days in the news and then it was forgotten, no one cares, most the police don't care. There are out of state dealers that will ship us mag kits, they charge a buck apiece to pull them apart before shipping. Your allowed to buy parts to replace the mag body or internals if a pre-ban mag is damaged or breaks. You can own the kits for rebuilds, just don't put the kits together.

[sandsnow]

People are doing the same here with parts kits.

There is an extra added twist here in CA.

CADOJ monitors people at the Reno Gunshow buying Hi-Cap mags and will bust you once you get across.

http://www.calguns.net/calgunforum/s...d.php?t=475344

[Punch The Clown]

LP, I can't believe I finally found a firearm that you don't own! Schriv, I got the gas system pretty much figured out. I really had a nice size leak where the gas tube threads into the block. I'm 99% sure the thing will run now.

[timshufflin]

1. Is there an update on how this thing runs?
2. Do you finally have REAL photos of this INTERNATIONAL treasure?

[Punch The Clown]

Yes Shufflin, it runs. Now, I have decided that the rifle has a terrible flaw for a battle rifle and the M14 was probably the better choice. If the FAL short strokes for whatever reason you are dead. #1-The rifle's bolt does not have any camming action therefore it relies on brute force to extract a fired cartridge. #2-The ejector is part of the receiver and not the bolt.
What does this mean? If the rifle short strokes it completely extracts the case but does not eject it. Now the bolt slams the fired case back into the chamber with the force of a jackhammer. Unless you can call a "Time-Out" and get out a steel cleaning rod and a hammer to remove the case you are f***ed! Fortunately in our case there is nobody shooting back but the M1/M14 is a better design, in my opinion. As far as looking bad to the bone the FAL gets the big thumbs up.

[timshufflin]

Whatever, I'll never be a fan of the m14. I don't like that rifle.

[Orlando]

Whatever, I'll never be a fan of the m14. I don't like that rifle.

How come Timma?

[timshufflin]

How come Timma?

How many press fit pins can you have in one rifle? If I'm being honest, I don't like stuff that requires a hammer and punch should something need attention.