timshufflin
09-13-2011, 01:16 PM
I have 6 oprods for sale and need more oprods to replace them so here's what I have and the terms I offer. All these oprod do pass the tilt test and operated fine on my test rifle despite the inadequacies of any measurements. Still, I am giving the measurements because I know that's all that matters to some folks.
The oprods I'm looking for in these trades need not have good pistons, may have rust the last 8" of the oprod by piston end, need not pass tilt test, but MUST have good tabs.
Here's the official oprod specs for good oprods;
Oprod specs.
Piston Diameter: .5260 to .5253 (under .5250 calls for rejection)
Piston Thickness: .190 to .155
Tab/Lug Height: .320 to .317 (under .310 calls for rejection)
Tab/Lug Thickness: .100 to .095
Tab/Lug Width: .265 to .235
1. I have a -1 SA cut. I'm asking for 3 oprods in trade for it and $10
The piston is .5258 to .5265 TW .2469 TH .311 TT .0859
Sold 2. I have a "-W.R.A." winchester UN CUT. I'm asking for 5 oprods in trade for it and $10. The piston is .5252 to .5253 TW .236 TH .3086 TT .086
3. I have an UN CUT -6 SA. I'm asking for two oprods in trade for it and $10. The piston is .5252 to .5247 TW .225 TH .320 TT .092
4. I have an UN CUT -9 curve side SA. I'm asking for two oprods in trade for it and $10. The piston is .519 to .524 TW .242 TH .306 TT .0827
Sold 5. I have an UN CUT -9 flat side SA. I'm asking for two oprods in trade for it. The piston is .5252 all the way around. TW .265 TH .317 TT .093
6. I have an UN CUT -9 flat side SA. I'm asking for two oprods in trade for it. The piston is .5253 all the way around. TW .259 TH .3156 TT .086
First "I'll take it" for each oprod gets them. If you have counter offers, EMAIL me.
The oprods I'm looking for in these trades need not have good pistons, may have rust the last 8" of the oprod by piston end, need not pass tilt test, but MUST have good tabs.
Here's the official oprod specs for good oprods;
Oprod specs.
Piston Diameter: .5260 to .5253 (under .5250 calls for rejection)
Piston Thickness: .190 to .155
Tab/Lug Height: .320 to .317 (under .310 calls for rejection)
Tab/Lug Thickness: .100 to .095
Tab/Lug Width: .265 to .235
1. I have a -1 SA cut. I'm asking for 3 oprods in trade for it and $10
The piston is .5258 to .5265 TW .2469 TH .311 TT .0859
Sold 2. I have a "-W.R.A." winchester UN CUT. I'm asking for 5 oprods in trade for it and $10. The piston is .5252 to .5253 TW .236 TH .3086 TT .086
3. I have an UN CUT -6 SA. I'm asking for two oprods in trade for it and $10. The piston is .5252 to .5247 TW .225 TH .320 TT .092
4. I have an UN CUT -9 curve side SA. I'm asking for two oprods in trade for it and $10. The piston is .519 to .524 TW .242 TH .306 TT .0827
Sold 5. I have an UN CUT -9 flat side SA. I'm asking for two oprods in trade for it. The piston is .5252 all the way around. TW .265 TH .317 TT .093
6. I have an UN CUT -9 flat side SA. I'm asking for two oprods in trade for it. The piston is .5253 all the way around. TW .259 TH .3156 TT .086
First "I'll take it" for each oprod gets them. If you have counter offers, EMAIL me.